top of page



Installing Signature Autosports Off-Road Gear bolt-on Rock Slider Steps on your Defender 90/110/130 is a great way to enhance your vehicle's protection and add functional style. Here's a step-by-step guide to help you with the installation:
Tools and Materials Needed
• Socket set (ratchet and various sockets)
• Wrench set
• Torque wrench
• Allen wrenches (if needed for specific bolts)
• Lubricant (optional, for easier bolt insertion)
• Cleaning cloth
• Safety glasses and gloves
***Hold up step mounting points and mark holes that need drilling if your chassis does not already provide holes. Check chassis harness if you need to drill, so you do not clip the harness.
Defender 90 Installation Steps
1. Preparation:
• Park your Defender on a flat surface and engage the parking brake.
• Lay out all the components of the rock sliders and the provided hardware. Check for any missing parts.
2. Clean the Area:
• Clean the mounting area on the vehicle's chassis where the sliders will attach. Remove any dirt or debris to ensure a secure fit.
3. Position the Rock Slider Steps:
• With the help of a friend, position the rock slider steps against the side of the vehicle, aligning them with the mounting holes. There are (3) three mounting points on each side of the vehicle, where the slider mounts bolt to the frame: Front (1 factory, pre-drilled holes), Center (2 factory, pre-drilled holes), and Rear (1 tubular mount). Please see the images provided below. Ensure that the sliders are level and correctly positioned.

Installation Instructions
Signature Autosports Offroad Gear
Rock Slider Steps for the Defender 90/110/130
SKU: SAS-DEF1-RSS
4. Attach the Rock Sliders:
-
***CRUCIAL: Thread each bolt by only 3-5 threads. DO NOT
fully tighten them yet, as you will need to adjust the position in order to get all bolts threaded in. -
Start by inserting REAR tubular wing through the rear sleeve and tightening by using the provided spacer and nut on the end of it.
-
Next, by reusing the FRONT bolt/nut on the vehicle already, Attach the FRONT Mounting point by threading the existing stud/nut.
-
Now, hold up your rear mounting point to the flange end of the tubular sleeve, and install your provided hardware loosely to hold the side step up.
-
Next, attach your center support arm for the CENTER mounting by aligning the chassis mounted side to the (2) holes in the chassis and use the long bolts to loosely mount these support brackets. Then, line up your center support bracket with your CENTER mounting point on your step. Use the provided bolts to loosely hold these together.
-
Once all bolts are threaded and your step is held up, go ahead and tighten all your bolts.
Provided Hardware used per mounting location PER SIDE:
• Front Mounting Point: Re-Use Factory provided bolt/nut
• Center Mounting Point: (2) M10x1.5 - 110mm w/ Washers and nuts (Factory holes are pre-drilled) + (2) M10x1.5 - 40mm
• Rear Mounting Point: (1) Provided tubular sleeve mount with washer/nut on the end + (2) M10x1.5 - 40mm w/Washers and nuts
5. Check Alignment:
• Step back and check that the rock slider steps are aligned properly and level.
• Make any necessary adjustments before tightening.
6. Tighten the Bolts:
• Using the torque wrench, tighten all the bolts to the manufacturer’s specified torque settings. If you don't have a specific torque setting, snug the bolts without over-tightening.
• Tighten in a crisscross pattern to distribute the pressure evenly.
7. Final Inspection:
• Once all bolts are tightened, inspect the installation for any movement or misalignment.
Ensure that all tools and materials are removed from the work area.
8. Test:
• Gently test the sliders by applying some weight to ensure they are securely installed.
Defender 110/130 Installation Steps
1. Preparation:• Park your Defender on a flat surface and engage the parking brake.• Lay out all the components of the rock sliders and the provided hardware. Check for any missing parts.
2. Clean the Area:• Clean the mounting area on the vehicle's chassis where the sliders will attach. Remove any dirt or debris to ensure a secure fit.
3. Position the Rock Slider Steps:• With the help of a friend, position the rock slider steps against the side of the vehicle, aligning them with the mounting holes. There are (4) four mounting points on each side of the vehicle, where the slider mounts bolt to the frame: Front (1 factory stud), (2) Center Support brackets (2 factory, pre-drilled holes per side), and Rear (1 bracket mount under cab door hinge). Please see the images provided below. Ensure that the sliders are level and correctly positioned.
4. Attach the Rock Sliders:
-
***CRUCIAL: Thread each bolt by only 3-5 threads. DO NOT
fully tighten them yet, as you will need to adjust the position in order to get all bolts threaded in. -
Start by by reusing the FRONT bolt/nut on the vehicle already, Attach the FRONT Mounting point by threading the existing stud/nut.
-
Now, hold up your rear mounting point to the flange and install your provided hardware loosely to hold the side step up.
-
Next, attach your center support arm for the CENTER mounting by aligning the chassis mounted side to the (2) holes in the chassis and use the long bolts to loosely mount these support brackets for both forward and rear brackets on both sides. Then, line up your center support brackets with your forward and rear mounting points on your step. Use the provided bolts to loosely hold these together.
-
Once all bolts are threaded and your step is held up, go ahead and tighten all your bolts.
Provided Hardware used per mounting location PER SIDE:
• Front Mounting Point: Re-Use Factory provided bolt/nut
• Center Mounting Point: (2) M10x1.5 - 110mm w/ Washers and nuts (Factory holes are pre-drilled) + (2) M10x1.5 - 40mm
• Rear Mounting Point: (1) Provided tubular sleeve mount with washer/nut on the end + (2) M10x1.5 - 40mm w/Washers and nuts
5. Check Alignment:
• Step back and check that the rock slider steps are aligned properly and level.
• Make any necessary adjustments before tightening.
6. Tighten the Bolts:
• Using the torque wrench, tighten all the bolts to the manufacturer’s specified torque settings. If you don't have a specific torque setting, snug the bolts without over-tightening.
• Tighten in a crisscross pattern to distribute the pressure evenly.
7. Final Inspection:
• Once all bolts are tightened, inspect the installation for any movement or misalignment.
Ensure that all tools and materials are removed from the work area.
8. Test:
• Gently test the sliders by applying some weight to ensure they are securely installed.
Maintenance Tips
• Periodically check the tightness of the bolts after installation, especially after off-road use.
• Clean the rock sliders regularly to prevent rust and maintain appearance.
You’re now ready to hit the trails with your newly installed rock slider steps! If you encounter any issues during installation, refer to the manufacturer’s instructions or consult a professional. Now go outside and enjoy your adventures!
IMPORTANT: If you are not confident installing this product yourself, please seek a professional to complete the installation.
Disclaimer for Automotive Product Self-Installation
By choosing to install this automotive product yourself, you acknowledge and accept the following terms, and by proceeding with the installation, you accept these terms and acknowledge that you do so at your own risk.:
• Skill and Knowledge: You confirm that you have the necessary skills, knowledge, and tools to perform the installation safely and correctly. If you are unsure, we recommend seeking professional assistance.
• Use of Product: This product is intended for use as specified by the manufacturer. Improper installation may lead to malfunctions, damage to your vehicle, or personal injury.
• Warranty Limitations: Self-installation may void any warranties associated with the product or your vehicle. Please review the warranty details before proceeding.
• Liability Waiver: The manufacturer and seller are not liable for any damages, injuries, or losses resulting from improper installation or use of the product.
• Compliance with Laws: You are responsible for ensuring that your installation complies with all local laws and regulations.




bottom of page
